![]() You can also specify an interface’s name to view only information about that interface. Type ifconfig to view the status of all currently active network interfaces, including their names. It’s also a quick way to view IP addresses and other network interface information. The ifconfig command has a variety of options to configure, tune, and debug your system’s network interfaces. “Link beat detected” means the cable is plugged in. Run the command to see the status of all interfaces or specify a specific interface to view its status. The ifplugstatus command will tell you whether a cable is plugged into a network interface or not. The whois command will show you a website’s whois records, so you can view more information about who registered and owns a specific website. Give it an IP address and you’ll see the associated domain name. Give it a domain name and you’ll see the associated IP address. Press q or Ctrl-C to quit when you’re done. mtr will continue to send packets, showing you the ping time to each “hop.” This will also show you any problems - in this case, we can see that hop 6 is losing over 20% of the packets. The mtr command combines ping and tracepath into a single command. If you’re having network problems or slowness, tracepath can show you where the network is failing or where the slowness is occurring. tracepath traces the network path to a destination you specify and reports each “hop” along the path. It’s also installed by default on Ubuntu, while traceroute isn’t. The tracepath command is similar to traceroute, but it doesn’t require root privileges. You can specify a finite amount of packets with the -c switch. It might help you a bit further.Unlike the ping command on Windows, the Linux ping command will keep sending packets until you terminate it. Hence: the report will not be printed (but Navision gives no errormessage). PRINTER03 can be assigned with NE01 on your workstation, while it being assigned NE02 on your collegues workstation. However, this always refers to the full name, this PRINTER03:NExx. However, when creating a report in Navision, you can assign a default printer, and only one printer. Then you connect the networkprinters, which will be assigned with NE02, NE03 and NE04. ![]() A faxdriver can also be used as printer driver, and will be given the name FAX:NE01. So, if a user connect their Epson inkjetprinter locally to the workstation, it will be assigned with the name EPSON:NE00. However, as networkprinters are disconnected when a user log offs, the localprinters will be assigned with the lowest numbers. And then connect printer01, which will be assigned with printer01:NE02. If the sequence is changed, so are the NE numbers. It will be assigned with printer02:ne01, et cetera. No problem sofar, as long as all printers are connected in the same sequence. When a workstation is connected to the printer, by means of a logonscript or manually, it also gets an NE number assigned by Windows. All printers have different names, let's say printer01, printer02 and printer03. While the name should be sufficient for Navision, all printers are referenced with the full name, thus including the NE0x assignment. ![]() Why did it change to Ne03?īoth local printers and networkprinters are uniquely identified with both the name and the ID number. But when I checked the settings again today and clicked on the Lookup arrow, I see "HP LaserJet 4200n MD1 Ne03". In other words, when I first assigned the remote printer to our remote users months ago it read "HP Laserjet 4200n MD1 Ne01". They changed randomly, and I'm not sure why. What I DID notice was the value " Ne0*" at the end of the printer names. It seemed to work well except for the instances I mentioned above. Navision THINKS it was printed, but no paper came out, and nothing in print queue on our terminal server.ĭuring our initial Navision implementation, I went to G/L setup area, and selected "Printer Selections" and assigned the remote printer to each of our remote users to force them to use it. It's been working for 7 months and suddenly skips. Today one of the other computers didn't print the control report for our picking slip. ![]() Only skips the final register printout each time). It simply won't print on one of the computers (but it WILL print on other remote computers, and it DOES print test report each time. Most of the time it's okay, but they have consistent problems printing the Item Journal register. They are tunneling into our local servers here in California, but printing back where they are in Maryland. We're experiencing printing problems with our remote users over VPN. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |